Pretraživanje priručnika
Kobelco Compact Seal CX-500Brtve statvene cijevi podmazivane uljem (krmena i pramčana), str. 30 … This method eliminates
the need to move the propeller or propeller shaft to replace the sealing rings and … Kobelco Compact Seal CX-500Brtve statvene cijevi podmazivane uljem (krmena i pramčana), str. 24 … The forward
chrome steel liner is tightened with bolts to the split clamp ring mounted to the propeller … Kobelco Compact Seal CX-500Brtve statvene cijevi podmazivane uljem (krmena i pramčana), str. 28 … the clearance
between the stern tube bearing and propeller
shaft. Measurements are taken at the oiling
hole (TOP … Nantong QN6004Kombinirani stroj: tokarilica / bušilica / glodalica / blanjalica, str. 13 … Turning feeding chain
53
3 aud Left thread
Spindle u—3-» Shaftz— 53
3,
Shaft wl, Right thread … Nantong QN6004Kombinirani stroj: tokarilica / bušilica / glodalica / blanjalica, str. 11 … 147
31, Shaft I —9125_, shaftyy
kee
~4 Shaft XW > Rocker Reciprocation of the planing machine
>_> Shaft VI … Nantong QN6004Kombinirani stroj: tokarilica / bušilica / glodalica / blanjalica, str. 44 … NAME
SKETCH
QTY!
SITUATION
QN6004-4201
NUT
=
at the shaft
with handle
10 (Fig.11) or
saddle and … MAN B&W L23/30H — radne karticeČetverotaktni pomoćni dizelski motor (agregat), str. 174 … 7)
Press the rear drive shaft bearing (58) onto
the drive shaft.
8)
Slide the small bearing retainer … MAN B&W L23/30H — radne karticeČetverotaktni pomoćni dizelski motor (agregat), str. 173 … 20)
Remove the large drive shaft bearing retainer
(53) using a screwdriver.
21)
Press the rear drive shaft … TeamTec Golar OG 200Brodsko spalionica (uljni mulj, mulj otpadnih voda i kruti otpad), str. 51 … Pull the shaft out as far-as possible. Put an ink mark on the shaft against the back … MAN B&W L23/30H — radne karticeČetverotaktni pomoćni dizelski motor (agregat), str. 185 … Dismounting is only possible by
damaging the shaft bush. Press out the shaft bushes.
12)
Pressure control valve … Westfalia OSA 7Samočisteći centrifugalni separator ulja (pročistač mazivog ulja), str. 71 … 6) Remove clutch pulleys from pump shaft end and worm wheel shaft end.
A 2178-000 - 3/22 -
Tanabe LSHC-20B/30A/40ADvostupanjski klipni kompresor hlađen zrakom (nužni / radni zrak), str. 25 … Take out the crank shaft
through the larger hole on the front side
(flywheel side) of crank case … TeamTec Golar OG 200Brodsko spalionica (uljni mulj, mulj otpadnih voda i kruti otpad), str. 125 … Clean the motor shaft and apply a rust prevention material
3. Push the pump shaft, item No. 4 … MAN B&W L23/30H — tehničke informacijeČetverotaktni pomoćni dizelski motor (agregat), str. 123 … If the pump leaks and the shaft sealing rings are worn,
it is recommended to replace the shaft … Westfalia OSA 7Samočisteći centrifugalni separator ulja (pročistač mazivog ulja), str. 72 … 3) Loosen
4) Use puller 406 to withdraw clutch drum from worm wheel shaft end,
Fig. 3/35 … Hamworthy Super Trident ST6ABiološki uređaj za obradu otpadnih voda, IMO MEPC.2(VI), str. 69 … f)
Remove the impeller screw and tab washer and withdraw the impeller from the motor shaft.
g) Remove … Westfalia OSC 4Samočisteći centrifugalni separator ulja, str. 102 … 3.4.6.1 Mounting the clutch driver
The motor power is transmitted to the worm wheel shaft … Nakakita — hidrauličko upravljanje ventilimaHidrauličko daljinsko upravljanje ventilima, str. 80 … The hand wheel (57), is fitted to the screw shaft (34)
( by squared hole & shaft fits ) and the … Westfalia OSC 4Samočisteći centrifugalni separator ulja, str. 106 … Hold a hard wooden block against the worm wheel
shaft and hammer it lightly to drive out the … TeamTec Golar OG 200Brodsko spalionica (uljni mulj, mulj otpadnih voda i kruti otpad), str. 130 … kit GKJ6D
> J3 shaft 109757 J 7 rot.A gear kit GKI7A
J4 shaft 131767 J7 rot.C … Westfalia OSA 7Samočisteći centrifugalni separator ulja (pročistač mazivog ulja), str. 73 … Place a hard wood block on worm wheel shaft end and rap it lightly
with a hammer to … Westfalia OSC 4Samočisteći centrifugalni separator ulja, str. 105 … Force the clutch drum off the cone of the worm wheel shaft
- with hex head screws 3 and … Tanabe LSHC-20B/30A/40ADvostupanjski klipni kompresor hlađen zrakom (nužni / radni zrak), str. 23 … Bearing (Crank Shaft, Connecting Rod)
(1)
(2)
Main bearings, supporting the crank shaft,
consist of precision taper roller …