Zhenjiang FH75
Free-fall lifeboat launching appliance
Stern launching arrangement for a BH-F7.8 type totally enclosed free-fall lifeboat: a welded ramp with rollers, a hydraulic A-frame davit with boat winch for launching and recovery by falls, the release hook unit, the fitted (gripping chain) unit and the forward lashing with hydrostatic release. The boat can be launched by free fall at up to 10° trim and 20° list, by falls, or floats free if the ship sinks. The manual gives the technical data, construction, weekly checks, wire renewal rules and step-by-step launching and recovery.
Click a part on the model to see its number and purpose.Open the 3D manual
Training videos
Maintenance procedures
Launching by free fall
- Confirm the boat's slingers are not connected to the fall chain hooks; leave the fitted unit, it does not affect a free-fall launch. p. 15
- Crew board and fasten the seat belts. p. 15
- Secure loose objects and close all openings. p. 15
- Start the boat engine. p. 16
- Open the release hook with the release mechanism inside the boat. p. 16
- The boat slides down the ramp into the water and leaves the ship. p. 16
Launching by falls
- Start the pump motor. p. 16
- Hang the slingers on both sides of the boat on the hooks of the boat fall chains. p. 16
- Open the slip hook of the fitted unit so the fitted plate turns up clear of the hook. p. 16
- Crew board. p. 16
- Open the release hook from inside the boat. p. 16
- Open the change valve of the cylinders: the davit arms move fully outboard. p. 16
- Open the change valve of the winch and lower the boat to the sea. p. 16
- Unhook the slingers and stow them in the slinger box; start the engine and leave the ship. p. 16
Float-free release
- When the ship sinks, water pressure separates the forward lashing and the fitted unit. p. 16
- The boat floats up and the release hook separates automatically. p. 16
- The crew board the floating boat, start the engine and leave the ship. p. 16
Recovering the boat
- Swing the arms out and hang the slingers on the fall chain hooks. p. 16
- Open the slip hook of the fitted unit. p. 17
- Hoist with the winch change valve; the limit switch stops the winch at the set position. p. 17A free-fall boat can be recovered only with the hydraulic drive
- Turn the arms inboard with the cylinder change valve; the boat enters the ramp. p. 17
- Hang on the long link of the forward lashing, then the release hook. p. 17
- When the arms are home, stop the cylinder; take the slingers off the fall hooks and stow them. p. 17
- Close the slip hook of the fitted unit so the boat is held firmly. p. 17
Maintenance intervals
| Item | When | Action | Manual |
|---|---|---|---|
| Davit and boat winch | weekly | Operate and check by the appointed person | p. 15 |
| Release hook, fitted unit, pivot unit, hydrostatic release | weekly | Check; make sure the boat can be secured and released quickly | p. 15 |
| Rollers, release hook, pivot unit, sheaves | often | Fill with grease | p. 15 |
| Davit falls | not more than 2 months | Turn end for end | p. 15 |
| Davit falls | when 10 % worn, diameter shrunk, twisted or deformed | Renew | p. 15 |
Technical specifications
| Max. working load | 75 kN | p. 14 |
|---|---|---|
| Max. hoisting load | 56 kN | p. 14 |
| Rope hoisting speed | > 3 m/min | p. 14 |
| Davit weight | about 9000 kg | p. 14 |
| Free-fall launch possible at | trim up to 10°, list up to 20° | p. 14 |
| Launch by falls possible at | trim up to 2°, list up to 5° | p. 14 |
| Hydraulic working pressure | 15 MPa | p. 22 |
| Relief valve setting | 17 MPa | p. 22 |
| Hydraulic oil | N46 (ISO VG46) | p. 4 |
| Wire rope | 18 × 19 non-rotating, galvanised | p. 4 |
| Applicable boat | BH-F7.8 free-fall lifeboat or similar | p. 4 |
| Rules | SOLAS MSC.47(66), LSA Code MSC.48(66), tests per IMO A.689(17) | p. 14 |
Spare parts and catalogue numbers
| Part | Number | Qty | Manual |
|---|---|---|---|
| Arm support bolt M24×60 (GB5783) with nut M24 and washer 24 | GB5783 M24×60 | 4 | p. 24 |
| Arm support rubber pad | 215ZF507-04-2 | 1 | p. 24 |
| Arm support square steel □250×250×9 | 1 | p. 24 | |
| Arm support plate | 215ZF507-04-3 | 2 | p. 24 |
| Fitted unit gripping block | 215ZF510-10-2-0 | p. 28 | |
| Fitted unit gripping chain | 215ZF510-10-1-0 | p. 28 | |
| Fitted unit bolt M16×70 (GB5783) with nut | M16×70 | p. 28 | |
| Release hook unit | 215ZF506-14-0 | 1 | p. 2 |
| Boat fall unit | 215ZF506-06-0 | 1 | p. 2 |
| Fitted boat unit | 215ZF510-06-0 | 1 | p. 2 |
| Limit unit | 215ZF510-12-0 | 1 | p. 2 |
| Aft lashing | 215ZF506-12-0 | 1 | p. 3 |
| Pipe system | 215ZF507-02-0 | 1 | p. 2 |
Source: manufacturer's manual “FH75 free-fall lifeboat launching appliance”, 33 pages. Page numbers refer to the original. Check against the manual on board before work.