SeaVint

Zhenjiang FH75

Free-fall lifeboat launching appliance

Stern launching arrangement for a BH-F7.8 type totally enclosed free-fall lifeboat: a welded ramp with rollers, a hydraulic A-frame davit with boat winch for launching and recovery by falls, the release hook unit, the fitted (gripping chain) unit and the forward lashing with hydrostatic release. The boat can be launched by free fall at up to 10° trim and 20° list, by falls, or floats free if the ship sinks. The manual gives the technical data, construction, weekly checks, wire renewal rules and step-by-step launching and recovery.

Kliknite dio na modelu da vidite njegov broj i namjenu.Otvori 3D priručnik

Videozapisi za obuku

Postupci održavanja

Launching by free fall

  1. Confirm the boat's slingers are not connected to the fall chain hooks; leave the fitted unit, it does not affect a free-fall launch. str. 15
  2. Crew board and fasten the seat belts. str. 15
  3. Secure loose objects and close all openings. str. 15
  4. Start the boat engine. str. 16
  5. Open the release hook with the release mechanism inside the boat. str. 16
  6. The boat slides down the ramp into the water and leaves the ship. str. 16

Launching by falls

  1. Start the pump motor. str. 16
  2. Hang the slingers on both sides of the boat on the hooks of the boat fall chains. str. 16
  3. Open the slip hook of the fitted unit so the fitted plate turns up clear of the hook. str. 16
  4. Crew board. str. 16
  5. Open the release hook from inside the boat. str. 16
  6. Open the change valve of the cylinders: the davit arms move fully outboard. str. 16
  7. Open the change valve of the winch and lower the boat to the sea. str. 16
  8. Unhook the slingers and stow them in the slinger box; start the engine and leave the ship. str. 16

Float-free release

  1. When the ship sinks, water pressure separates the forward lashing and the fitted unit. str. 16
  2. The boat floats up and the release hook separates automatically. str. 16
  3. The crew board the floating boat, start the engine and leave the ship. str. 16

Recovering the boat

  1. Swing the arms out and hang the slingers on the fall chain hooks. str. 16
  2. Open the slip hook of the fitted unit. str. 17
  3. Hoist with the winch change valve; the limit switch stops the winch at the set position. str. 17
    A free-fall boat can be recovered only with the hydraulic drive
  4. Turn the arms inboard with the cylinder change valve; the boat enters the ramp. str. 17
  5. Hang on the long link of the forward lashing, then the release hook. str. 17
  6. When the arms are home, stop the cylinder; take the slingers off the fall hooks and stow them. str. 17
  7. Close the slip hook of the fitted unit so the boat is held firmly. str. 17

Intervali održavanja

StavkaKadaRadnjaPriručnik
Davit and boat winchweeklyOperate and check by the appointed personstr. 15
Release hook, fitted unit, pivot unit, hydrostatic releaseweeklyCheck; make sure the boat can be secured and released quicklystr. 15
Rollers, release hook, pivot unit, sheavesoftenFill with greasestr. 15
Davit fallsnot more than 2 monthsTurn end for endstr. 15
Davit fallswhen 10 % worn, diameter shrunk, twisted or deformedRenewstr. 15

Tehničke specifikacije

Max. working load75 kNstr. 14
Max. hoisting load56 kNstr. 14
Rope hoisting speed> 3 m/minstr. 14
Davit weightabout 9000 kgstr. 14
Free-fall launch possible attrim up to 10°, list up to 20°str. 14
Launch by falls possible attrim up to 2°, list up to 5°str. 14
Hydraulic working pressure15 MPastr. 22
Relief valve setting17 MPastr. 22
Hydraulic oilN46 (ISO VG46)str. 4
Wire rope18 × 19 non-rotating, galvanisedstr. 4
Applicable boatBH-F7.8 free-fall lifeboat or similarstr. 4
RulesSOLAS MSC.47(66), LSA Code MSC.48(66), tests per IMO A.689(17)str. 14

Rezervni dijelovi i kataloški brojevi

DioBrojKol.Priručnik
Arm support bolt M24×60 (GB5783) with nut M24 and washer 24GB5783 M24×604str. 24
Arm support rubber pad215ZF507-04-21str. 24
Arm support square steel □250×250×91str. 24
Arm support plate215ZF507-04-32str. 24
Fitted unit gripping block215ZF510-10-2-0str. 28
Fitted unit gripping chain215ZF510-10-1-0str. 28
Fitted unit bolt M16×70 (GB5783) with nutM16×70str. 28
Release hook unit215ZF506-14-01str. 2
Boat fall unit215ZF506-06-01str. 2
Fitted boat unit215ZF510-06-01str. 2
Limit unit215ZF510-12-01str. 2
Aft lashing215ZF506-12-01str. 3
Pipe system215ZF507-02-01str. 2

Izvor: priručnik proizvođača „FH75 free-fall lifeboat launching appliance”, 33 str. Brojevi stranica odnose se na izvornik. Prije rada provjerite priručnik na brodu.

Stranica je automatski prevedena. Brojevi dijelova, kôdovi i stranice su kao u izvorniku.