SeaVint

Zhenjiang SAPC21

Single-arm slewing boat and raft davit

Single-arm davit for launching and recovering a rescue boat, davit-launched liferafts or a work boat; it also serves as a provision crane. Hoisting is electric (or by hand), lowering is by gravity with a speed limiter and weighted brake, slewing is hydraulic from a pump station or, without power, from an accumulator. Lowering can be controlled from inside the boat or raft with remote wires; an automatic release hook frees the raft when it floats. The manual covers data, adjustment of brake and interlocks, operation, liferaft hook use, maintenance, the control box and motor faults.

Kliknij część na modelu, aby zobaczyć jej numer i przeznaczenie.Otwórz instrukcję 3D

Filmy szkoleniowe

How a ship's rescue boat works: release hook, picking up a person, casualty care▶ YouTube Shorts

Procedury obsługi

Commissioning and launching the boat or raft

  1. Start the pump station motor, open the oil filling shut-off valve and switch on the solenoid valve. s. 22
  2. Press the hoisting button until the boat or raft is above the deck, then release it. s. 22
  3. Slew to port or starboard with the manual directional valve. s. 22
  4. Raise the bobweight: the boat lowers by its own weight at the limited speed; lower the bobweight to stop. s. 22
    Keep the bobweight fully raised while lowering so the brake lining does not wear
  5. From inside the boat: pull the slewing wires to swing out, then the lowering wire to lower; let go to stop. s. 22
  6. In an emergency open the accumulator shut-off valve and repeat the steps above. s. 22

Hoisting by hand and rapid return of the empty hook

  1. Take the manual handle out of its stowage; the motor circuit is switched off. s. 22
  2. Insert it in the socket for hoisting by hand and turn. s. 23
  3. For several liferafts: after the first raft is unhooked, insert the handle in the rapid-return socket and wind the empty hook back. s. 23
  4. Hook on the next raft, hoist it outboard by hand and launch. s. 23

Using the automatic release hook

  1. Lower the hook from the davit head. s. 23
  2. Pull the activating/release lever down with a sharp jerk to open the hook. s. 23
  3. Engage the raft shackle or ring and close the hook by pushing the lever fully up; the safety pin goes in automatically. s. 23
  4. Hoist, slew to the lowering point, fasten bowsing and steering lines and board the raft; then let them go. s. 23
  5. Lower and pull the red lanyard with a sharp jerk before the raft reaches the water; the hook opens when the raft floats. s. 23
    Hook stays closed with more than 13.5 kg on it

Adjusting the brake and interlocks

  1. Fill the gear box and the pump station tank with the specified oils. s. 21
  2. Raise the bobweight, start the hoisting motor and check the drum turns the right way. s. 21
  3. If the brake slips too far, loosen the lower screws of the brake rod, mark the gear rings, move the bobweight one or two teeth up and retighten. s. 21
  4. Check: with the manual handle out every power is off; with the bobweight raised the motor cannot hoist; the motor stops when the hook reaches the block under the davit head. s. 22
  5. Set the slewing limit device so the arm cannot strike the hull. s. 22

Interwały obsługi technicznej

ElementKiedyCzynnośćInstrukcja
Hoisting gear box oilafter the first 6 months, then periodicallyReplace and clean the boxs. 25
Grease nipplesoftenFill with greases. 25
Speed limiter friction liningperiodicallyCheck wear, replace if neededs. 25
Pump station oilperiodicallyCheck level and qualitys. 25
Accumulator oil pressureperiodicallyRecharge with the pump to about 17 MPa when the alarm comess. 25
Accumulator nitrogenperiodicallyDrain the oil and check; recharge to about 10 MPa if lows. 25
Control boxevery half monthGeneral check with power offs. 33
Control boxevery 3 monthsExtensive overhauls. 33

Usterki i co robić

Dane techniczne

Max. working load21 kNs. 20
Hoisting load14 kNs. 20
Max. slewing load14 kNs. 20
Hoisting speed> 18 m/mins. 20
Lowering speedabout 40–48 m/mins. 20
Wire ropeØ15.5 mm, 18 × 7, 155 kg/mm², min. breaking load 150 kNs. 4
Drum capacity25 ms. 5
Brake setting load21 kNs. 5
Slewing angle (pump station)270°s. 4
Slewing angle (accumulator)> 10°s. 4
Hoisting motorY132M-6-H, 5.5 kW 50 Hz / 6.3 kW 60 Hzs. 4
Pump motorY112M-4-Hs. 10
Hydraulic working pressure14 MPas. 10
Relief valve setting19 MPas. 10
Hydraulic oilYB-N46s. 10
AccumulatorNXQ2-F40/315-Hs. 10
Gear oilN46 mechanical oil, max. 60 °Cs. 5
Control box supply3 phase 380–440 V, control 220 Vs. 32
RulesSOLAS 1974 with 1983 and 1992 amendments, IMO A.689(17)s. 20

Części zamienne i numery katalogowe

CzęśćNumerSzt.Instrukcja
Hydraulic motorXJA500-D1s. 10
AccumulatorNXQ2-F40/315-H1s. 10
Counter-balance valveLHDV33-21W-E6-60/601s. 10
Pressure relayDG34 (100–400 bar)1s. 10
Manual directional valve1s. 10
Pressure gauge 0–40 MPaYC-601s. 10
Pressure gauge switchKF-L8/14E1s. 10
Throttle check valveRD111s. 10
Ball valve Dg6 320 barBKH2s. 10
Return line filterRFA-25X20L1s. 10
Check valveRC-1F2s. 10
Pump motorY112M-4-H1s. 10
Hydraulic pump1s. 10
Release handle1s. 7
Remote control ropeabout 10 ms. 7

Źródło: instrukcja producenta „SAPC21 single arm slewing boat and raft davit”, 77 stron. Numery stron według oryginału. Przed pracą sprawdź instrukcję na statku.

Strona przetłumaczona automatycznie. Numery części, kody i strony są jak w oryginale.