SeaVint

Zhenjiang SAPC21

Single-arm slewing boat and raft davit

Single-arm davit for launching and recovering a rescue boat, davit-launched liferafts or a work boat; it also serves as a provision crane. Hoisting is electric (or by hand), lowering is by gravity with a speed limiter and weighted brake, slewing is hydraulic from a pump station or, without power, from an accumulator. Lowering can be controlled from inside the boat or raft with remote wires; an automatic release hook frees the raft when it floats. The manual covers data, adjustment of brake and interlocks, operation, liferaft hook use, maintenance, the control box and motor faults.

点击模型上的零件,查看编号和用途。打开 3D 说明书

培训视频

How a ship's rescue boat works: release hook, picking up a person, casualty care▶ YouTube Shorts

保养规程

Commissioning and launching the boat or raft

  1. Start the pump station motor, open the oil filling shut-off valve and switch on the solenoid valve. 第 22 页
  2. Press the hoisting button until the boat or raft is above the deck, then release it. 第 22 页
  3. Slew to port or starboard with the manual directional valve. 第 22 页
  4. Raise the bobweight: the boat lowers by its own weight at the limited speed; lower the bobweight to stop. 第 22 页
    Keep the bobweight fully raised while lowering so the brake lining does not wear
  5. From inside the boat: pull the slewing wires to swing out, then the lowering wire to lower; let go to stop. 第 22 页
  6. In an emergency open the accumulator shut-off valve and repeat the steps above. 第 22 页

Hoisting by hand and rapid return of the empty hook

  1. Take the manual handle out of its stowage; the motor circuit is switched off. 第 22 页
  2. Insert it in the socket for hoisting by hand and turn. 第 23 页
  3. For several liferafts: after the first raft is unhooked, insert the handle in the rapid-return socket and wind the empty hook back. 第 23 页
  4. Hook on the next raft, hoist it outboard by hand and launch. 第 23 页

Using the automatic release hook

  1. Lower the hook from the davit head. 第 23 页
  2. Pull the activating/release lever down with a sharp jerk to open the hook. 第 23 页
  3. Engage the raft shackle or ring and close the hook by pushing the lever fully up; the safety pin goes in automatically. 第 23 页
  4. Hoist, slew to the lowering point, fasten bowsing and steering lines and board the raft; then let them go. 第 23 页
  5. Lower and pull the red lanyard with a sharp jerk before the raft reaches the water; the hook opens when the raft floats. 第 23 页
    Hook stays closed with more than 13.5 kg on it

Adjusting the brake and interlocks

  1. Fill the gear box and the pump station tank with the specified oils. 第 21 页
  2. Raise the bobweight, start the hoisting motor and check the drum turns the right way. 第 21 页
  3. If the brake slips too far, loosen the lower screws of the brake rod, mark the gear rings, move the bobweight one or two teeth up and retighten. 第 21 页
  4. Check: with the manual handle out every power is off; with the bobweight raised the motor cannot hoist; the motor stops when the hook reaches the block under the davit head. 第 22 页
  5. Set the slewing limit device so the arm cannot strike the hull. 第 22 页

保养周期

项目周期操作说明书
Hoisting gear box oilafter the first 6 months, then periodicallyReplace and clean the box第 25 页
Grease nipplesoftenFill with grease第 25 页
Speed limiter friction liningperiodicallyCheck wear, replace if needed第 25 页
Pump station oilperiodicallyCheck level and quality第 25 页
Accumulator oil pressureperiodicallyRecharge with the pump to about 17 MPa when the alarm comes第 25 页
Accumulator nitrogenperiodicallyDrain the oil and check; recharge to about 10 MPa if low第 25 页
Control boxevery half monthGeneral check with power off第 33 页
Control boxevery 3 monthsExtensive overhaul第 33 页

故障及处理方法

技术参数

Max. working load21 kN第 20 页
Hoisting load14 kN第 20 页
Max. slewing load14 kN第 20 页
Hoisting speed> 18 m/min第 20 页
Lowering speedabout 40–48 m/min第 20 页
Wire ropeØ15.5 mm, 18 × 7, 155 kg/mm², min. breaking load 150 kN第 4 页
Drum capacity25 m第 5 页
Brake setting load21 kN第 5 页
Slewing angle (pump station)270°第 4 页
Slewing angle (accumulator)> 10°第 4 页
Hoisting motorY132M-6-H, 5.5 kW 50 Hz / 6.3 kW 60 Hz第 4 页
Pump motorY112M-4-H第 10 页
Hydraulic working pressure14 MPa第 10 页
Relief valve setting19 MPa第 10 页
Hydraulic oilYB-N46第 10 页
AccumulatorNXQ2-F40/315-H第 10 页
Gear oilN46 mechanical oil, max. 60 °C第 5 页
Control box supply3 phase 380–440 V, control 220 V第 32 页
RulesSOLAS 1974 with 1983 and 1992 amendments, IMO A.689(17)第 20 页

备件与目录号

零件编号数量说明书
Hydraulic motorXJA500-D1第 10 页
AccumulatorNXQ2-F40/315-H1第 10 页
Counter-balance valveLHDV33-21W-E6-60/601第 10 页
Pressure relayDG34 (100–400 bar)1第 10 页
Manual directional valve1第 10 页
Pressure gauge 0–40 MPaYC-601第 10 页
Pressure gauge switchKF-L8/14E1第 10 页
Throttle check valveRD111第 10 页
Ball valve Dg6 320 barBKH2第 10 页
Return line filterRFA-25X20L1第 10 页
Check valveRC-1F2第 10 页
Pump motorY112M-4-H1第 10 页
Hydraulic pump1第 10 页
Release handle1第 7 页
Remote control ropeabout 10 m第 7 页

来源:制造商说明书《SAPC21 single arm slewing boat and raft davit》,共 77 页。页码以原文为准。作业前请核对船上的说明书。

本页为自动翻译。零件号、代码和页码与原文一致。