SeaVint

Zhenjiang SAPC21

Single-arm slewing boat and raft davit

Single-arm davit for launching and recovering a rescue boat, davit-launched liferafts or a work boat; it also serves as a provision crane. Hoisting is electric (or by hand), lowering is by gravity with a speed limiter and weighted brake, slewing is hydraulic from a pump station or, without power, from an accumulator. Lowering can be controlled from inside the boat or raft with remote wires; an automatic release hook frees the raft when it floats. The manual covers data, adjustment of brake and interlocks, operation, liferaft hook use, maintenance, the control box and motor faults.

Нажмите на деталь на модели — увидите номер и назначение.Открыть 3D-мануал

Обучающие видео

How a ship's rescue boat works: release hook, picking up a person, casualty care▶ YouTube Shorts

Процедуры обслуживания

Commissioning and launching the boat or raft

  1. Start the pump station motor, open the oil filling shut-off valve and switch on the solenoid valve. стр. 22
  2. Press the hoisting button until the boat or raft is above the deck, then release it. стр. 22
  3. Slew to port or starboard with the manual directional valve. стр. 22
  4. Raise the bobweight: the boat lowers by its own weight at the limited speed; lower the bobweight to stop. стр. 22
    Keep the bobweight fully raised while lowering so the brake lining does not wear
  5. From inside the boat: pull the slewing wires to swing out, then the lowering wire to lower; let go to stop. стр. 22
  6. In an emergency open the accumulator shut-off valve and repeat the steps above. стр. 22

Hoisting by hand and rapid return of the empty hook

  1. Take the manual handle out of its stowage; the motor circuit is switched off. стр. 22
  2. Insert it in the socket for hoisting by hand and turn. стр. 23
  3. For several liferafts: after the first raft is unhooked, insert the handle in the rapid-return socket and wind the empty hook back. стр. 23
  4. Hook on the next raft, hoist it outboard by hand and launch. стр. 23

Using the automatic release hook

  1. Lower the hook from the davit head. стр. 23
  2. Pull the activating/release lever down with a sharp jerk to open the hook. стр. 23
  3. Engage the raft shackle or ring and close the hook by pushing the lever fully up; the safety pin goes in automatically. стр. 23
  4. Hoist, slew to the lowering point, fasten bowsing and steering lines and board the raft; then let them go. стр. 23
  5. Lower and pull the red lanyard with a sharp jerk before the raft reaches the water; the hook opens when the raft floats. стр. 23
    Hook stays closed with more than 13.5 kg on it

Adjusting the brake and interlocks

  1. Fill the gear box and the pump station tank with the specified oils. стр. 21
  2. Raise the bobweight, start the hoisting motor and check the drum turns the right way. стр. 21
  3. If the brake slips too far, loosen the lower screws of the brake rod, mark the gear rings, move the bobweight one or two teeth up and retighten. стр. 21
  4. Check: with the manual handle out every power is off; with the bobweight raised the motor cannot hoist; the motor stops when the hook reaches the block under the davit head. стр. 22
  5. Set the slewing limit device so the arm cannot strike the hull. стр. 22

Интервалы технического обслуживания

ЧтоКогдаЧто делатьМануал
Hoisting gear box oilafter the first 6 months, then periodicallyReplace and clean the boxстр. 25
Grease nipplesoftenFill with greaseстр. 25
Speed limiter friction liningperiodicallyCheck wear, replace if neededстр. 25
Pump station oilperiodicallyCheck level and qualityстр. 25
Accumulator oil pressureperiodicallyRecharge with the pump to about 17 MPa when the alarm comesстр. 25
Accumulator nitrogenperiodicallyDrain the oil and check; recharge to about 10 MPa if lowстр. 25
Control boxevery half monthGeneral check with power offстр. 33
Control boxevery 3 monthsExtensive overhaulстр. 33

Неисправности и что делать

Технические характеристики

Max. working load21 kNстр. 20
Hoisting load14 kNстр. 20
Max. slewing load14 kNстр. 20
Hoisting speed> 18 m/minстр. 20
Lowering speedabout 40–48 m/minстр. 20
Wire ropeØ15.5 mm, 18 × 7, 155 kg/mm², min. breaking load 150 kNстр. 4
Drum capacity25 mстр. 5
Brake setting load21 kNстр. 5
Slewing angle (pump station)270°стр. 4
Slewing angle (accumulator)> 10°стр. 4
Hoisting motorY132M-6-H, 5.5 kW 50 Hz / 6.3 kW 60 Hzстр. 4
Pump motorY112M-4-Hстр. 10
Hydraulic working pressure14 MPaстр. 10
Relief valve setting19 MPaстр. 10
Hydraulic oilYB-N46стр. 10
AccumulatorNXQ2-F40/315-Hстр. 10
Gear oilN46 mechanical oil, max. 60 °Cстр. 5
Control box supply3 phase 380–440 V, control 220 Vстр. 32
RulesSOLAS 1974 with 1983 and 1992 amendments, IMO A.689(17)стр. 20

Запчасти и номера по каталогу

ДетальНомерКол.Мануал
Hydraulic motorXJA500-D1стр. 10
AccumulatorNXQ2-F40/315-H1стр. 10
Counter-balance valveLHDV33-21W-E6-60/601стр. 10
Pressure relayDG34 (100–400 bar)1стр. 10
Manual directional valve1стр. 10
Pressure gauge 0–40 MPaYC-601стр. 10
Pressure gauge switchKF-L8/14E1стр. 10
Throttle check valveRD111стр. 10
Ball valve Dg6 320 barBKH2стр. 10
Return line filterRFA-25X20L1стр. 10
Check valveRC-1F2стр. 10
Pump motorY112M-4-H1стр. 10
Hydraulic pump1стр. 10
Release handle1стр. 7
Remote control ropeabout 10 mстр. 7

Источник: мануал производителя «SAPC21 single arm slewing boat and raft davit», 77 стр. Номера страниц указаны по оригиналу. Перед работой сверяйтесь с мануалом на судне.

Страница переведена автоматически. Номера деталей, коды и страницы — как в оригинале.