Zhenjiang SAPC21
Single-arm slewing boat and raft davit
Single-arm davit for launching and recovering a rescue boat, davit-launched liferafts or a work boat; it also serves as a provision crane. Hoisting is electric (or by hand), lowering is by gravity with a speed limiter and weighted brake, slewing is hydraulic from a pump station or, without power, from an accumulator. Lowering can be controlled from inside the boat or raft with remote wires; an automatic release hook frees the raft when it floats. The manual covers data, adjustment of brake and interlocks, operation, liferaft hook use, maintenance, the control box and motor faults.
Training videos
Maintenance procedures
Commissioning and launching the boat or raft
- Start the pump station motor, open the oil filling shut-off valve and switch on the solenoid valve. p. 22
- Press the hoisting button until the boat or raft is above the deck, then release it. p. 22
- Slew to port or starboard with the manual directional valve. p. 22
- Raise the bobweight: the boat lowers by its own weight at the limited speed; lower the bobweight to stop. p. 22Keep the bobweight fully raised while lowering so the brake lining does not wear
- From inside the boat: pull the slewing wires to swing out, then the lowering wire to lower; let go to stop. p. 22
- In an emergency open the accumulator shut-off valve and repeat the steps above. p. 22
Hoisting by hand and rapid return of the empty hook
- Take the manual handle out of its stowage; the motor circuit is switched off. p. 22
- Insert it in the socket for hoisting by hand and turn. p. 23
- For several liferafts: after the first raft is unhooked, insert the handle in the rapid-return socket and wind the empty hook back. p. 23
- Hook on the next raft, hoist it outboard by hand and launch. p. 23
Using the automatic release hook
- Lower the hook from the davit head. p. 23
- Pull the activating/release lever down with a sharp jerk to open the hook. p. 23
- Engage the raft shackle or ring and close the hook by pushing the lever fully up; the safety pin goes in automatically. p. 23
- Hoist, slew to the lowering point, fasten bowsing and steering lines and board the raft; then let them go. p. 23
- Lower and pull the red lanyard with a sharp jerk before the raft reaches the water; the hook opens when the raft floats. p. 23Hook stays closed with more than 13.5 kg on it
Adjusting the brake and interlocks
- Fill the gear box and the pump station tank with the specified oils. p. 21
- Raise the bobweight, start the hoisting motor and check the drum turns the right way. p. 21
- If the brake slips too far, loosen the lower screws of the brake rod, mark the gear rings, move the bobweight one or two teeth up and retighten. p. 21
- Check: with the manual handle out every power is off; with the bobweight raised the motor cannot hoist; the motor stops when the hook reaches the block under the davit head. p. 22
- Set the slewing limit device so the arm cannot strike the hull. p. 22
Maintenance intervals
| Item | When | Action | Manual |
|---|---|---|---|
| Hoisting gear box oil | after the first 6 months, then periodically | Replace and clean the box | p. 25 |
| Grease nipples | often | Fill with grease | p. 25 |
| Speed limiter friction lining | periodically | Check wear, replace if needed | p. 25 |
| Pump station oil | periodically | Check level and quality | p. 25 |
| Accumulator oil pressure | periodically | Recharge with the pump to about 17 MPa when the alarm comes | p. 25 |
| Accumulator nitrogen | periodically | Drain the oil and check; recharge to about 10 MPa if low | p. 25 |
| Control box | every half month | General check with power off | p. 33 |
| Control box | every 3 months | Extensive overhaul | p. 33 |
Faults and what to do
Technical specifications
| Max. working load | 21 kN | p. 20 |
|---|---|---|
| Hoisting load | 14 kN | p. 20 |
| Max. slewing load | 14 kN | p. 20 |
| Hoisting speed | > 18 m/min | p. 20 |
| Lowering speed | about 40–48 m/min | p. 20 |
| Wire rope | Ø15.5 mm, 18 × 7, 155 kg/mm², min. breaking load 150 kN | p. 4 |
| Drum capacity | 25 m | p. 5 |
| Brake setting load | 21 kN | p. 5 |
| Slewing angle (pump station) | 270° | p. 4 |
| Slewing angle (accumulator) | > 10° | p. 4 |
| Hoisting motor | Y132M-6-H, 5.5 kW 50 Hz / 6.3 kW 60 Hz | p. 4 |
| Pump motor | Y112M-4-H | p. 10 |
| Hydraulic working pressure | 14 MPa | p. 10 |
| Relief valve setting | 19 MPa | p. 10 |
| Hydraulic oil | YB-N46 | p. 10 |
| Accumulator | NXQ2-F40/315-H | p. 10 |
| Gear oil | N46 mechanical oil, max. 60 °C | p. 5 |
| Control box supply | 3 phase 380–440 V, control 220 V | p. 32 |
| Rules | SOLAS 1974 with 1983 and 1992 amendments, IMO A.689(17) | p. 20 |
Spare parts and catalogue numbers
| Part | Number | Qty | Manual |
|---|---|---|---|
| Hydraulic motor | XJA500-D | 1 | p. 10 |
| Accumulator | NXQ2-F40/315-H | 1 | p. 10 |
| Counter-balance valve | LHDV33-21W-E6-60/60 | 1 | p. 10 |
| Pressure relay | DG34 (100–400 bar) | 1 | p. 10 |
| Manual directional valve | 1 | p. 10 | |
| Pressure gauge 0–40 MPa | YC-60 | 1 | p. 10 |
| Pressure gauge switch | KF-L8/14E | 1 | p. 10 |
| Throttle check valve | RD11 | 1 | p. 10 |
| Ball valve Dg6 320 bar | BKH | 2 | p. 10 |
| Return line filter | RFA-25X20L | 1 | p. 10 |
| Check valve | RC-1F | 2 | p. 10 |
| Pump motor | Y112M-4-H | 1 | p. 10 |
| Hydraulic pump | 1 | p. 10 | |
| Release handle | 1 | p. 7 | |
| Remote control rope | about 10 m | p. 7 |
Source: manufacturer's manual “SAPC21 single arm slewing boat and raft davit”, 77 pages. Page numbers refer to the original. Check against the manual on board before work.