SeaVint

Chapter 4. Navigation and communications

37 questions with how to answer each.

4.1.1 ECDIS set up and operation Core

Do the Master and navigation officers know the company procedures for setting up and operating the ship's ECDIS units, and do records show the ECDIS was used in line with those procedures throughout every stage of the voyage?

In one lineSafety settings derived from draught and UKC, set by the Master, recorded; alarms active; route checked; back-up ready.

How to answer
  • Explain how the safety contour and safety depth are calculated from draught, squat and UKC requirement, and show the current values
  • State who is authorised to change the settings and where changes are logged
  • Demonstrate route check, alarm settings and the display mode used
  • Explain the action on primary ECDIS failure: switch to back-up, record, inform the Master
  • Show the ECDIS checklists completed for the last voyage
Have ready
  • ECDIS units with current settings displayed
  • ECDIS procedures in the SMS
  • Safety settings record/log
  • Voyage checklists (pre-departure, pre-arrival)
  • Route check reports
  • ECDIS software and chart data status

4.1.2 Operation and testing of radar/ARPA Core

Do the Master and navigation officers know the company procedures for operating and managing the ship's radar/ARPA units, and do records show they were operated and tested according to those procedures?

In one lineRadars checked and recorded; sea-stabilised for collision avoidance; know X vs S band; AIS only supplementary.

How to answer
  • Explain the routine checks: performance monitor, heading marker alignment, gyro and log inputs, recorded at the required interval
  • Explain that sea-stabilised mode is used for collision avoidance (true aspect) and ground-stabilised for navigation
  • Explain that X-band gives better resolution and detects SARTs, while S-band is better in rain and sea clutter
  • Explain why AIS data should not be the sole basis for collision avoidance (missing targets, data errors, not every vessel transmits)
  • Demonstrate setting up a parallel index line and ARPA guard zones
Have ready
  • Radar/ARPA units
  • Radar performance check records
  • Bridge checklists and logbook entries
  • Manufacturer's operating manual
  • Radar service reports

4.1.3 Operating and testing the steering control systems Rotational 1

Do the Master and navigation officers know how the company requires the steering control systems to be used and tested, and do records prove this was done?

In one lineI can change steering modes including emergency control; tests and three-monthly drills done and recorded.

How to answer
  • Demonstrate changing from autopilot to hand steering and to non-follow-up/emergency control
  • Explain the pre-departure steering test and show the checklist
  • Explain the emergency steering drill: communication with steering gear room, changeover to local control, recording
  • Explain how you test the off-course alarm and how often
  • Describe the actions on a steering alarm: hand steer, call the Master, inform the engine room, check pumps
Have ready
  • Steering gear test records and checklists
  • Emergency steering drill records
  • Steering changeover instructions posted on bridge and in steering gear room
  • Deck logbook entries
  • Off-course alarm test record

4.1.4 Automatic Identification System (AIS) Rotational 1

Do the Master and navigation officers know the company procedures for using the AIS, and do records confirm that regular checks and tests were done according to those procedures?

In one lineAIS data correct for current voyage; annual test done; AIS is only an aid, never the sole collision avoidance tool.

How to answer
  • Show the AIS display and confirm voyage data are correct for the current voyage
  • Explain when the data are updated (each departure, status change at anchor or berth)
  • Show the annual test record and any routine checks
  • Explain why AIS is supplementary to radar and visual lookout for collision avoidance
  • Explain that switching off is only allowed where safety or security demands it, and must be logged
Have ready
  • AIS unit and display
  • AIS annual test certificate/report
  • Logbook entries for AIS data updates or switch-off
  • Company AIS procedure

4.1.5 Bridge Navigational Watch Alarm System (BNWAS) Rotational 1

Do the Master and navigation officers know the company procedure for using the BNWAS, and do records show it was operated and tested according to that procedure?

In one lineBNWAS on at sea, key with Master; alarm stages known; tested and logged; on stage 2 alarm go straight to the bridge.

How to answer
  • Explain that BNWAS must be on whenever the ship is underway at sea and the controls are restricted to the Master
  • Describe the alarm sequence: visual on bridge, audible on bridge, then alarm to the Master/back-up officer and further locations
  • Demonstrate the test and show the test records
  • Explain your action on a stage 2 alarm: go to the bridge at once and check the OOW's condition and the navigational situation
Have ready
  • BNWAS panel and key control
  • BNWAS test records
  • Logbook entries for switching on/off
  • Master's standing orders on BNWAS

4.1.6 Global Navigation Satellite System(s) Rotational 2

Do the Master and navigation officers know the company procedures for managing and operating the GNSS receivers fitted on board, and are these receivers set up, used and checked according to the procedures?

In one lineGNSS correctly configured, cross-checked with radar/visual fixes, and I know how to spot jamming or spoofing.

How to answer
  • Explain which receiver feeds which equipment and how to switch to the secondary
  • Show the datum and confirm it matches the chart datum used in ECDIS
  • Explain how GNSS positions are cross-checked with radar or visual fixes at the required interval
  • Explain how you would recognise and respond to GNSS jamming or spoofing
Have ready
  • GNSS receivers and settings menu
  • Position cross-check records in logbook
  • GNSS procedure in SMS
  • Manufacturer's manual

4.1.7 Echo sounder Rotational 2

Do the Master and navigation officers know the company rules for using and managing the echo sounder, and are there records showing it was tested and used as the company expects?

In one lineEcho sounder set to correct offset; I can calculate depth under keel; accuracy checked and recorded.

How to answer
  • Explain how the echo sounder reference is set and show the draught/offset currently entered
  • Calculate depth under keel from the displayed reading for the inspector
  • Explain how accuracy is checked and show the record
  • State when the echo sounder must be running (coastal, pilotage, approaches) and the shallow alarm setting
Have ready
  • Echo sounder and its settings
  • Accuracy check records
  • Recorder print-outs or data logs
  • Bridge checklists

4.1.8 Speed and distance measuring devices Rotational 2

Do the Master and navigation officers know the company procedures for operating and testing the speed and distance measuring devices, and do records show periodic tests were done as required?

In one lineLog type and speed mode known; accuracy checked against GNSS and recorded; feeds ARPA correctly.

How to answer
  • Explain the log type and whether it gives speed through the water or over the ground
  • Explain why speed through water matters for ARPA sea-stabilised collision avoidance
  • Show the record of accuracy checks against GNSS speed and any correction applied
  • Explain the action if the log fails (manual speed input, inform the Master)
Have ready
  • Speed log and display
  • Log accuracy check records
  • Logbook entries
  • Service reports

4.1.9 Navigation lights and shapes Rotational 2

Do the Master and navigation officers know the company procedures for using and testing navigation lights and shapes, and is there evidence that the lights were tested for full function and correct visibility?

In one lineLights and alarms tested and visually checked, spares on board, shapes ready and I know when to show them.

How to answer
  • Explain the test routine: controller test, failure alarm check, visual check on deck, recorded in the log
  • Show spare bulbs and where the shapes are stored
  • Explain which shapes are shown at anchor, not under command, restricted in ability to manoeuvre and constrained by draught
  • Explain what is done if a light fails
Have ready
  • Navigation light controller
  • Navigation light test records
  • Spare bulbs
  • Day shapes in their locker
  • Logbook entries

4.1.10 NAVTEX and SafetyNET Rotational 2

Do the Master and navigation officers know the company procedure for handling Maritime Safety Information received via NAVTEX and SafetyNET, and have warnings that affect the route been plotted on the voyage charts?

In one lineCorrect NAVTEX/EGC areas set; warnings reviewed, logged and plotted on the route; expired ones removed.

How to answer
  • Explain how NAVTEX stations are selected for the route and which message types cannot be disabled
  • Show the EGC settings for the current NAVAREA and coastal areas
  • Show how a relevant warning is plotted on ECDIS (manual update/user chart) or paper charts
  • Explain how the log of warnings in force is maintained and cancellations removed
Have ready
  • NAVTEX receiver and settings
  • EGC/SafetyNET receiver and area settings
  • Navigational warnings file or log
  • Charts/ECDIS showing plotted warnings

4.1.11 Preserving data from the VDR/S-VDR Rotational 2

Do the Master and navigation officers know the company procedure for saving VDR/S-VDR data, and are there records showing the equipment tests were completed as required?

In one lineI know how to save VDR data after an incident; annual performance test valid; alarms checked.

How to answer
  • Explain how to save VDR data after an incident and demonstrate the location of the save function
  • Explain that after an incident the Master decides on saving and the data must not be overwritten
  • Show the latest annual performance test certificate
  • Explain the routine checks of the VDR alarm panel and microphones
Have ready
  • VDR control panel
  • VDR annual performance test certificate
  • VDR check records
  • Company VDR procedure

4.1.12 Magnetic and gyro compasses Rotational 2

Do the Master and navigation officers know the company procedures for the magnetic and gyro compasses on board, and are there records showing these are accurate and reliable?

In one lineCompass error checked each watch and recorded; deviation card current; I can switch gyros safely.

How to answer
  • Explain how compass error is obtained (azimuth, amplitude, transit) and how often
  • Show the compass error book and the deviation card
  • Demonstrate or explain how to switch between gyros and check repeaters afterwards
  • Explain what you do when a gyro error is large or a gyro alarm occurs
Have ready
  • Compass error book
  • Deviation card and compass adjustment certificate
  • Gyro changeover instructions
  • Logbook entries

4.1.13 VHF/DSC transceivers Rotational 2

Do the Master and navigation officers know the company procedures for operating and testing the VHF/DSC sets, and are there records showing periodic tests and checks were done as the company expects?

In one lineVHF/DSC tested and logged daily; COLREGs come first; VHF agreements for collision avoidance carry risk.

How to answer
  • Explain and demonstrate the DSC test and show where it is recorded in the GMDSS log
  • Confirm the position input is automatic from GNSS or updated manually
  • Explain the risks of VHF in collision avoidance: misidentification, delay, agreements that conflict with COLREGs
  • State that COLREG action comes first, VHF only to support it
Have ready
  • VHF/DSC sets
  • GMDSS radio log
  • Company procedure on VHF use
  • Distress instruction card

4.1.14 Daylight signalling lamp Rotational 2

Do the Master and navigation officers know how the company requires the daylight signalling lamp to be tested and used?

In one lineDaylight lamp tested, battery charged, spares available, recorded.

How to answer
  • Show where the lamp is kept and test it
  • Explain its independent power supply (battery) and how it is kept charged
  • Show spare bulbs and test records
  • Explain when it may be used (signalling, emergency)
Have ready
  • Daylight signalling lamp
  • Spare bulbs
  • Test records

4.1.15 Sound signalling equipment Rotational 2

Do the Master and navigation officers know the company procedures for using and testing the ship's sound signalling equipment, and are there records confirming regular tests and correct use?

In one lineWhistle tested and logged; I know manoeuvring and restricted visibility signals under the COLREGs.

How to answer
  • Show the whistle test record and explain how it is tested (before departure)
  • Demonstrate the automatic fog signal setting
  • State the signals: one short (altering to starboard), two short (port), three short (astern), five short (doubt)
  • State restricted visibility signals: one prolonged every 2 minutes making way, two prolonged when stopped, one prolonged and two short for vessels not under command, restricted in ability to manoeuvre or constrained by draught
Have ready
  • Whistle and fog signal controller
  • Bell and gong
  • Test records
  • Logbook entries

4.2.1 Passage planning Core

Do the Master and navigation officers know the company passage planning procedures, and has every voyage been appraised, planned, carried out and monitored in line with those procedures, industry good practice and local and international rules?

In one lineBerth-to-berth plan: appraisal, no-go areas, abort points, contingencies; approved, signed, followed and monitored.

How to answer
  • Walk the inspector through the current passage plan from berth to berth
  • Explain the sources used in appraisal: charts, sailing directions, routeing guides, NAVTEX, port information, weather
  • Point out no-go areas, safety margins, abort points and contingency anchorages on the ECDIS
  • Explain the fixing interval and methods for each leg and show the records
  • Explain how the plan is changed during the voyage and re-approved by the Master
Have ready
  • Passage plan with Master's approval and officers' signatures
  • ECDIS route and route check report
  • Deck logbook and position records
  • Company passage planning checklist
  • Pilot cards and port information

4.2.2 Under keel clearance (UKC) policy Core

Do the Master and navigation officers know the company under keel clearance policy and procedure, and do records show UKC was calculated at the right points of each voyage and the ship stayed within the policy?

In one lineUKC calculated for departure, transit critical points and arrival, all factors included; waivers documented.

How to answer
  • State the company UKC minimums for each phase of the voyage
  • Walk the inspector through a recent UKC calculation showing each factor (squat, tide, density, ZOC/chart accuracy)
  • Show calculations for the shallowest points on the route, not just the berth
  • If a waiver was needed, show the correspondence with the office and the extra precautions taken
Have ready
  • UKC calculation forms or software outputs
  • Company UKC policy
  • Passage plan showing critical depth points
  • Office waivers and correspondence
  • Tide tables and port information on depths

4.2.3 Master's Standing Orders and Daily Orders Rotational 1

Has the Master written Standing Orders, supported by Daily (Night) Orders, that reinforce company navigation expectations, including restricted visibility, CPA/BCR limits and minimum passing distances from dangers and navigation aids, and have all navigation officers signed to show they understand them?

In one lineStanding Orders signed and understood; Night Orders daily; CPA/BCR, passing distance and call-Master rules followed.

How to answer
  • Summarise the key Standing Orders: when to call the Master, minimum CPA/BCR, passing distances, restricted visibility actions
  • Show your signature on the Standing Orders and the latest Night Orders
  • Give an example of when you called the Master according to the orders and show the log entry
  • Explain that Standing Orders are aligned with and do not reduce company requirements
Have ready
  • Master's Standing Orders signed by all officers
  • Night/Daily Order book
  • Deck logbook entries
  • Company navigation procedures

4.2.4 Electronic chart management Rotational 2

Do the Master and navigation officers know how the company requires electronic charts to be managed, and are the ENCs and RNCs on board managed, corrected and used correctly?

In one lineENCs updated weekly, T&P and AIO reviewed, permits cover the voyage, RNC use controlled.

How to answer
  • Explain the update cycle: receive weekly updates, apply, verify and record
  • Show the chart update/status report confirming charts are up to date
  • Explain how T&P notices are applied and how the AIO is displayed and checked against the route
  • Explain when RNCs are used and the extra precautions (RCDS mode, appropriate paper charts)
  • Show permits and coverage for the entire voyage
Have ready
  • ECDIS chart status report
  • Weekly update records
  • ENC permits and licences
  • AIO and T&P records
  • Chart catalogue for the voyage

4.2.5 Paper chart management Rotational 1

Do the Master and navigation officers know the company procedures for managing paper charts, and are paper charts on board managed, corrected and used correctly?

In one linePaper charts corrected to latest Notice, recorded in the log, T&P managed and scale suitable.

How to answer
  • Explain the correction procedure: weekly Notices, tracing, apply in ink, record on chart and in the log
  • Show the chart correction log and the last correction applied
  • Explain how T&P notices are handled
  • Explain how the chart folio is checked against the voyage before departure
Have ready
  • Chart correction log
  • Weekly Notices to Mariners
  • Corrected paper charts
  • Chart catalogue

4.2.6 Testing navigational equipment, main propulsion, steering gear and thrusters Rotational 1

Do the Master and navigation officers know the company requirements for testing navigation equipment, main engine, steering gear and thrusters before use and before critical phases, and do checklists or log entries confirm these tests were done?

In one linePre-departure/arrival checklists complete; steering, engine and thrusters tested before use and recorded.

How to answer
  • Walk the inspector through the pre-departure checklist and show it completed for the last departure
  • Explain the steering gear test and when it is done
  • Explain the main engine and thruster tests and the communication with the engine room
  • Explain the extra checks before critical phases: pilotage, narrow channels, berthing
Have ready
  • Pre-departure and pre-arrival checklists
  • Steering gear test records
  • Deck and engine logbooks
  • Bridge-engine room communication test records

4.2.7 Nautical publications Rotational 2

Do the Master and navigation officers know the company procedure for carrying and managing nautical publications, and is there evidence that publications have been managed accordingly?

In one lineRequired publications current and corrected; electronic ones updated; new editions ordered on time.

How to answer
  • Explain which publications are required and how they are checked against the company list
  • Show the last correction applied and the correction record
  • Explain how electronic publications are updated and verified
  • Explain the ordering process for new editions
Have ready
  • Nautical publications (paper and electronic)
  • Publication correction records
  • Company list of required publications
  • Order records

4.3.1 Minimum bridge team composition Core

Do the Master and navigation officers know the company procedures that set the minimum bridge team and engine room operating mode, and do records show recent voyages were planned and carried out to those expectations?

In one lineBridge manning levels set in the plan for each stage and confirmed in the log; engine room mode matches.

How to answer
  • Explain the bridge manning levels defined by the company and when each is used
  • Show where the required level is marked in the passage plan
  • Show the logbook entries confirming bridge team and engine room mode changes
  • Explain how manning is increased in poor visibility or heavy traffic
Have ready
  • Company bridge manning procedure
  • Passage plan with manning levels
  • Deck logbook
  • Engine room logbook

4.3.2 Machinery space team composition Core

Do the engineer officers know the company procedures for machinery space operating mode and, where attendance is required, the engine room team composition for each voyage stage, and do records confirm the engine room was operated that way?

In one lineEngine room mode and manning set for each stage, communicated with the bridge and recorded.

How to answer
  • Explain when the engine room must be manned and the required team for each situation
  • Explain how the bridge informs the engine room of operational changes (standby, restricted visibility)
  • Show logbook entries confirming changes of mode and the team in attendance
  • Explain UMS checks before leaving the engine room unattended
Have ready
  • Engine room logbook
  • Company procedure on machinery space operating mode
  • UMS checklists
  • Communication records with bridge

4.3.3 Integrating a pilot (or similar role) into the bridge team Rotational 1

Do the Master and navigation officers know the company procedures for bringing a pilot (or a person with an equivalent role) into the bridge team, and do records show the procedure was followed?

In one linePilot card exchanged and explained; plan agreed; pilot monitored and challenged if needed.

How to answer
  • Explain the Master/pilot exchange: pilot card, passage plan comparison, tug and berthing plan
  • Explain each item on the pilot card (draught, displacement, engine and propeller details, thrusters, defects)
  • Explain how the OOW monitors the pilot: position checks, rudder/engine orders, challenge if concerned
  • Show the completed master/pilot exchange checklist
Have ready
  • Pilot card
  • Master/pilot exchange checklist
  • Wheelhouse poster
  • Passage plan for pilotage
  • Deck logbook

4.3.4 Bridge distractions Rotational 2

Do the Master and navigation officers know the company procedures for preventing disturbance and distraction on the bridge, and are those procedures followed?

In one lineBridge kept free of distractions: no personal devices, no non-essential visitors or tasks during critical phases.

How to answer
  • Explain the company rules on personal devices and visitors on the bridge
  • Explain how non-navigational tasks are minimised during critical phases
  • Describe how the Master limits radio and phone calls during pilotage
  • Point to posted instructions on bridge distractions
Have ready
  • Company procedure on bridge distractions
  • Posted bridge rules
  • Master's Standing Orders
  • Pilotage checklist

4.4.1 Emergency Position Indicating Radio Beacon (EPIRB) Rotational 2

Do the Master and officers know how to operate the EPIRB, and is it in good condition with records of its inspections, tests and maintenance?

In one lineEPIRB tested and maintained, expiry dates valid; manual activation known; false alert cancelled with RCC.

How to answer
  • Demonstrate the self-test as per maker's instructions and show the record
  • Explain how to activate it manually and how it activates automatically
  • Explain the action on accidental activation: switch off and inform the nearest RCC immediately
  • Show the annual test, shore-based maintenance record and expiry dates
Have ready
  • EPIRB and its float-free bracket
  • Maker's instructions
  • Annual test and shore-based maintenance certificates
  • Battery and hydrostatic release expiry labels
  • Registration documents

4.4.2 Search and Rescue Transmitters (SARTs) Rotational 2

Do the Master and officers know how to operate the SARTs, and are they in good condition with records of inspection and testing?

In one lineSART mounted high in the craft; shows as dots on X-band radar; tested and battery valid.

How to answer
  • Explain where the SARTs are stored and how they are mounted on the survival craft
  • Explain the radar SART display: line of dots outward from the SART's position, becoming arcs and then circles near the SART
  • Demonstrate the self-test and show the records
  • Point out the battery expiry date
  • If AIS-SART is fitted, explain how it appears as an AIS target
Have ready
  • SARTs and storage brackets
  • Test records
  • Battery expiry labels
  • Maker's instructions

4.4.3 Survival craft portable two-way VHF radios Rotational 2

Do the Master and officers know where the portable two-way VHF radios for survival craft are kept, what they are for and how to use them, and are they in good condition with records of inspections and tests?

In one lineTwo-way VHFs stored at the agreed location, tested on a working channel, emergency batteries sealed and valid.

How to answer
  • Show where the radios and their sealed emergency batteries are stored
  • Demonstrate a test on a working channel (not channel 16)
  • Explain that the sealed primary batteries are kept for emergency use only and have an expiry date
  • Show the test records
Have ready
  • Two-way VHF radios
  • Sealed primary batteries
  • Test records
  • Maker's instructions

4.4.4 Sending and receiving distress, urgency and safety messages Rotational 2

Do the Master and navigation officers know how to send and handle incoming distress, urgency and safety communications, and are suitable instructions posted next to the GMDSS equipment?

In one lineDesignated radio operator on the muster list; I can send DSC distress, urgency and safety messages; instructions posted.

How to answer
  • Name the designated person in charge of radio communications in distress and show this on the muster list
  • Walk the inspector through sending a DSC distress alert and the following voice message (MAYDAY, position, nature, assistance)
  • Explain urgency and safety message procedures
  • Explain how a received distress alert is handled (acknowledgement, relay, inform the Master) as described in IAMSAR Volume III
  • Point to the posted instructions
Have ready
  • GMDSS console with posted instructions
  • Muster list showing the radio operator
  • IAMSAR Volume III
  • GMDSS radio log

4.4.5 Operation and testing of GMDSS station Rotational 2

Do the Master and navigation officers know how to operate, test and maintain the GMDSS VHF, MF/HF and satellite equipment, and are there records showing the equipment is in good order?

In one lineGMDSS tested daily, weekly and monthly as required; logged; batteries checked; survey and maintenance valid.

How to answer
  • Explain the routine: daily DSC self-tests and battery checks, weekly test call with coast station, monthly check of portable equipment
  • Show the GMDSS radio log entries
  • Explain how the reserve source of energy is checked
  • Show the last radio survey and shore maintenance records
Have ready
  • GMDSS radio log
  • Radio survey and maintenance records
  • Battery records
  • Maker's manuals

4.4.6 Use of radio or mobile telephone equipment during cargo and ballast handling Rotational 2

Does everyone on board, from the Master to the ratings, understand the hazards of using radios or mobile phones during cargo and ballast handling, and does the ship carry enough intrinsically safe handheld radios for the working areas?

In one lineOnly intrinsically safe radios in cargo areas; no mobile phones on deck; enough radios available and charged.

How to answer
  • Explain why mobile phones and non-intrinsically safe radios are not used in hazardous areas during cargo or ballast operations
  • Show the intrinsically safe radios and their certification marking
  • Explain the company and terminal rules (ISGOTT guidance) on MF/HF and other transmitters in port
  • Explain charging and testing arrangements for the portable radios
Have ready
  • Intrinsically safe portable radios and certification labels
  • Company procedure on radio and phone use
  • Ship/shore safety checklist
  • Charging station

4.5.1 Annual DP Trial report and supporting exercises Rotational 2

On DP shuttle tankers, is the latest Annual DP Trial report on board, do the Master and officers know its contents, and have they practised a range of DP failure scenarios in onboard training and drills?

In one lineAnnual DP Trials report on board; findings known and closed; DP drills practised on varied scenarios.

How to answer
  • Explain when the last Annual DP Trials were conducted and the main findings
  • Describe key failure modes and the vessel's worst-case failure
  • Show the records of DP drills and the scenarios practised
  • Explain how trial findings were closed
Have ready
  • Annual DP Trials report
  • DP FMEA
  • DP drill records
  • Close-out records

4.5.2 DP Position Reference Systems Rotational 1

Do the Master and officers know the company procedures for using Position Reference Systems, is the equipment in good condition, and is sensor offset data easy for the DPO to find?

In one linePRS selected per offtake location, checked before ops, sensor offsets at hand for the DPO.

How to answer
  • Explain which PRS are used at each offtake location and why
  • Show the sensor offset data and where the DPO can find it
  • Explain the pre-operation checks for each PRS
  • Explain the action on PRS failure or degradation
Have ready
  • PRS equipment
  • Sensor offset data
  • DP checklists
  • Field operation guidelines

4.5.3 DP events and incidents Rotational 1

Do the Master and officers know how the company requires DP events and incidents to be reported and recorded, and is the DP system continuously logging all its parameters?

In one lineDP events reported and investigated per company procedure; parameters continuously logged and kept.

How to answer
  • Explain the company reporting procedure for DP events and incidents
  • Show the DP event log and logged parameters
  • Give an example of a recent event and how it was investigated
  • Explain how data are kept
Have ready
  • DP event and incident records
  • DP data logger
  • Company DP procedures
  • Investigation reports

4.5.4 DP operations manual Rotational 2

Is a complete DP operations manual on board, and do the Master and officers understand what it holds, such as DP checklists, capability plots, the consequence analysis and the ASOG (activity specific operating guidelines)?

In one lineDP manual on board; I use the checklists, capability plots, consequence analysis and ASOG during operations.

How to answer
  • Explain what the DP operations manual contains and where it is kept
  • Explain how capability plots are used to check the weather limits
  • Explain the consequence analysis alarm and the action on it
  • Explain the ASOG levels (normal, advisory, reduced, stop) and their triggers
Have ready
  • DP operations manual
  • DP checklists
  • Capability plots
  • ASOG

4.5.5 Field Operations Manuals Rotational 2

Are current Field Operations Manuals on board for every offshore terminal the ship trades to, do the Master and officers know what they contain, and are there records of routine communication tests with the offshore installations, as required by the Field Specific Operating Guidelines?

In one lineLatest Field Operations Manual and FSOG on board; communication checks recorded; contacts and channels known.

How to answer
  • Explain how the latest edition is verified with the terminal or company
  • Explain the content of the FSOG for the last terminal visited
  • Show the contact numbers, call signs and channels for operational and emergency use
  • Show the communication check records
Have ready
  • Field Operations Manuals
  • FSOG
  • Communication check records
  • Terminal contact lists

An independent guide written by seafarers for seafarers. It is not affiliated with or endorsed by OCIMF and does not reproduce the SIRE 2.0 Question Library: questions are put in our own words. The official library and guidance are published by OCIMF (ocimf.org). Always follow your company's SMS.