MacGregor-Hägglunds HH 160-0520
Electro-hydraulic hose handling crane
Instruction and parts manual for a MacGregor-Hägglunds HH 160-0520 electro-hydraulic deck crane used for handling cargo hoses: SWL 5 t, outreach 4–20 m, hook travel 40 m. The crane housing is also the hydraulic oil tank; one fixed-displacement pump driven by a 34 kW electric motor feeds the hoisting winch, the luffing cylinder and the slewing gear through a load-sensing main directional valve. The manual covers technical data and description, hydraulic and electric functions, the operating instruction and safety checklist, parking and sea stowing, the maintenance and lubricating charts, oil sampling and lubricants, service of the slewing gearset and hoisting winch, troubleshooting, and illustrated parts lists including the 5 t hook block.
Mga training video
Mga maintenance procedure
Starting and stopping the crane
- Notify the responsible officer and make sure nobody is in the crane working area. p. 51
- Check the ship lists no more than 5°, the wires run correctly in the sheaves and their ends are clamped, and the hydraulic oil level. p. 50
- Set the main switch on the starter box to 1: lamps 'Main supply' and 'Anticondensation heater' light. Switch on about 10 hours before use. p. 51
- Press Start on the starter box (or green Start on the remote box on the foundation): 'Crane running' lights and the heater lamp goes out. p. 51
- Operate with the three levers: hoisting, luffing and slewing. The motion follows the lever; several motions at once reduce the speed. p. 52
- Emergency stop: turn the emergency stop cock to stop all crane movements. p. 51Stops every movement
- Stop with the Stop button (or red Stop on the remote box), then set the main switch to 0. p. 51
Parking the crane and sea stowing
- Before the voyage put the jib on its parking support. p. 53
- If the hook is stowed to deck use fibre strops with low ultimate load or a manual turnbuckle. p. 53
- Do not tighten the wire ropes: ropes, sheaves and winches take heavy stress during the voyage. p. 53Never tension the hoisting wire for sea stowing
- Before cargo handling loosen the hook and jib before raising the jib from the support, and luff in to the working area. p. 53
- Release the hook from sea stowing manually: it starts hoisting when the brake is released. p. 53Release the hook by hand
Cleaning the crane housing / oil tank and refilling
- Immobilise the jib and stop the electric motor. p. 59
- Open the drain cock and drain into clean drums; then drain the rest at the plug on the pump bracket. p. 59
- Remove the tank cover, scrape out sediment with a rubber scraper and flush with white spirit. p. 59
- Wipe dry with clean rags (no cotton waste); refit the cover with new sealing compound. p. 59
- Fill filtered oil to just under MAX with the machinery at rest, jib parked and cylinder fully in. p. 59ISO 16/13 or better
Sampling hydraulic oil
- Run the system to 40–50 °C oil temperature. p. 60
- Connect a pressure gauge hose to gauge outlet 3.1 of the hoisting circuit. p. 60
- Run the hoisting winch at maximum hoisting speed and bleed 0.5 L into a bucket. p. 60
- Fill the sample bottle and send it for analysis. p. 60
- If contamination is too high change oil and filters, run about 1 h and take a new sample. p. 60
Replacing the hook block
- Order the hook block by part number 388 7531-801 (SWL 5 t). p. 129
- After replacing the hook block or genuine parts in it, carry out an overload test of the complete unit and issue a new certificate. p. 128Overload test and new certificate
Mga maintenance interval
| Item | Kailan | Gagawin | Manual |
|---|---|---|---|
| Crane housing / hydraulic oil tank | Before every start | Check the oil level in the sight glass | p. 54 |
| Oil filter | Before every start | Check the oil pressure | p. 54 |
| Slewing gear case and winch | Before every start | Check oil level; check for leakage, especially the bottom shaft seal | p. 54 |
| Slewing rim screws | Every 2 months / 200 h | Inspect from below; if any slackens, tighten all with a torque wrench | p. 54 |
| Slewing gear case and winch | After first 200 h | First oil change | p. 54 |
| Wire ropes and clamps | Every 6 months / 500 h | Inspect for wear as class and national rules require | p. 54 |
| Wire sheaves | Every 6 months / 500 h | Inspect for wear | p. 54 |
| Loose gear | Every 6 months / 500 h | Check that hook and swivel are intact | p. 54 |
| Cranehouse, foundation and jib welds | Every 6 months / 500 h | Inspect for cracks | p. 55 |
| Hydraulic oil | Every 6 months | Sample and analyse; without analysis change the oil every 2 years / 2000 h | p. 55 |
| Slewing pinion | Every 6 months / 500 h | Check backlash; check slewing rim seals | p. 55 |
| Slewing gear case and winch | Every year / 1000 h | Change oil, including the disc room and room between motor and gear; check slewing motor spline shaft | p. 55 |
| Air breather | Every year / 1000 h | Check and change | p. 55 |
| Hydraulic oil tank | Every 2 years / 2000 h | Drain, clean the tank, refill and change the filter cartridge | p. 55 |
| Winch and slewing gear disc brakes | Every 2 years / 2000 h | Check for leakage and check the discs | p. 55 |
| Slewing rim studs/screws | Every 4 years | Tighten all with a torque wrench to the slewing assembly drawing | p. 55 |
Mga sira at ang dapat gawin
Technical specifications
| Type of crane | HH 160-0520 | p. 37 |
|---|---|---|
| Safe working load (SWL) | 5 t | p. 37 |
| Jib radius | max 20 m / min 4.0 m | p. 37 |
| Hook travel (lifting height) | 40 m | p. 37 |
| Luffing time max to min radius | 50 s | p. 37 |
| Slewing speed | max 1.6 r/min | p. 37 |
| Steel rope | Ø13 mm, L = 105 m, part no. 388 7148-821 | p. 37 |
| Crane weight | 10.6 t | p. 37 |
| Electric motor | 34 kW cont., 48 kW S6 40%, 1765 r/min, 440 V 60 Hz, starting current 440 A | p. 37 |
| Hook block | SWL 5 t, part no. 388 7531-801 | p. 129 |
| Shackle on hook block | SWL 6.5 t, part no. 875 12102-001 | p. 129 |
| Hydraulic oil | about 46 cSt at 40 °C (e.g. Shell T46), filtered to ISO 16/13 or better | p. 62 |
| Winch and slewing gear oil | ISO VG 220 HM gear oil (e.g. Shell Omala 220) | p. 62 |
| Disc room / room between motor and gear | ATF oil (e.g. Shell ATF Donax TF) | p. 62 |
| Ship list for operation | max 5° | p. 50 |
Spare parts at catalogue number
| Piyesa | Numero | Dami | Manual |
|---|---|---|---|
| Winch, mounting, 5 tonnes | 288 0133-801 | 1 | p. 4 |
| Winch, 5 tonnes | 288 0132-801 | 1 | p. 4 |
| Hydraulic motor (winch) | 388 3127-801 | 1 | p. 4 |
| Slewing gear unit with disc brake | 287 9970-801 | 1 | p. 4 |
| Hydraulic motor, slewing | 187 8383-801 | 1 | p. 4 |
| Pump drive arrangement | 288 0710-801 | 1 | p. 4 |
| Pump | 187 8379-801 | 1 | p. 4 |
| Slewing assembly | 287 9972-801 | 1 | p. 4 |
| Slewing rim | 388 7097-801 | 1 | p. 4 |
| Jib top, mounting | 288 0136-801 | 1 | p. 4 |
| Cylinder mounting | 288 1646-801 | 1 | p. 4 |
| Load wire rope with thimble | 388 7148-821 | 1 | p. 4 |
| Hook block, SWL 5 t | 388 7531-801 | 1 | p. 129 |
| Hook (hook block) | 875 12001-004 | 1 | p. 129 |
| Sheave (hook block) | 875 12004-005 | 1 | p. 129 |
| Shaft (hook block) | 875 12005-003 | 1 | p. 129 |
| Roller bearing (hook block) | 875 12054-006 | 1 | p. 129 |
| Shackle SWL 6.5 t (hook block) | 875 12102-001 | 1 | p. 129 |
| Jib bearing assembly | 287 9974-801 | 1 | p. 4 |
| Directional valve | 188 1338-801 | 1 | p. 4 |
| Balance valve | 287 9466-801 | 2 | p. 4 |
| Motor valve | 388 6358-801 | 1 | p. 4 |
| Balance valve | 288 1561-801 | 1 | p. 4 |
| Filter | 287 9463-801 | 1 | p. 4 |
| Hydraulic cylinder | 287 9465-801 | 1 | p. 4 |
| El. central / starter | 314 3273-801 | 1 | p. 4 |
Pinagmulan: manual ng gumawa na “MacGregor_HH160-0520_hose_crane_manual”, 167 pahina. Ang numero ng pahina ay ayon sa orihinal. Suriin ang manual sa barko bago magtrabaho.
Awtomatikong isinalin ang pahinang ito. Ang part number, code at pahina ay ayon sa orihinal.