Zhenjiang PD10
Pneumatic accommodation ladder winch
Air-driven winch for hoisting and lowering the accommodation ladder, a short-time duty machine. A flanged air motor drives a split drum for two ropes through a reduction gear with a ratchet brake that limits the lowering speed; a hand crank on the gearbox shaft works it when there is no air, and a limit valve cuts the air while the crank is out. The manual covers readiness checks, operation with the three-position change valve, lubrication, rope renewal and opening the gearbox.
点击模型上的零件,查看编号和用途。打开 3D 说明书
培训视频
保养规程
Readiness for operation
- All operators must know the construction of the winch. 第 11 页
- The rope must leave the drum as on the general drawing; never wind it the wrong way. 第 11 页
- Check all connections for looseness, especially the rope end on the drum and the foundation bolts; check the brake. 第 11 页
- Clear any obstacles round the winch. 第 11 页
- Check the air fittings, pipes and air motor. 第 11 页
- Renew a rope with ten broken wires in 1 m or with reduced diameter. 第 11 页
- Check the oil level between the dipstick marks. 第 11 页
- Check the manual handle is stowed and the limit switch is reliable. 第 11 页
Operating the winch
- Pull out the pin on the accommodation ladder. 第 11 页
- Move the three-position change valve handle to lower, stop, hoist or capsize the ladder. 第 11 页
- To work by hand, keep the change valve in the middle, insert the handle on the square shaft end of the gearbox and crank. 第 12 页
Opening and reassembling the gearbox
- Unscrew the drain plug at the bottom of the gear box, drain the oil and remove the air motor. 第 12 页
- Strip the bolts of the big cover plate and pull it off together with the high-speed gear shaft; take out the bearings. 第 12 页
- Remove the big gear, ratchet and brake disc of the second stage in order. 第 12 页
- Reassemble in reverse order. 第 12 页Check the ratchet tooth direction; do not strip the ratchet unless necessary
- Refit only if the brake works without slipping. 第 12 页
保养周期
| 项目 | 周期 | 操作 | 说明书 |
|---|---|---|---|
| Gear box oil | after the first 50 h | Renew all oil and flush the case | 第 12 页 |
| Gear box oil | yearly | Change | 第 12 页 |
| Wire ropes | regularly | Smear with calcium base grease ZG-3 | 第 12 页 |
| Seals | regularly | Replace | 第 12 页 |
| Rope end on drum and foundation bolts | often | Check they are secure | 第 12 页 |
技术参数
| Rated load | 2 × 5 kN | 第 13 页 |
|---|---|---|
| Holding load | 2 × 5 kN | 第 13 页 |
| Rated hoisting speed | 0.14 m/s | 第 13 页 |
| Drum | Ø230 × (91 + 91) mm | 第 13 页 |
| Winding layers | 3 | 第 13 页 |
| Wire capacity | 2 × 15 m | 第 13 页 |
| Wire rope | 6 × 37 – Ø13 mm, 1700 MPa | 第 13 页 |
| Transmission ratio (air motor) | 75.43 | 第 13 页 |
| Transmission ratio (manual) | 30.73 | 第 13 页 |
| Total efficiency | 0.80 | 第 13 页 |
| Air motor | JFH 1/24, 4.41 kW, 890 r/min | 第 13 页 |
| Air consumption | 5.0 m³/min | 第 13 页 |
| Working pressure | 0.6 MPa | 第 13 页 |
| Overall dimensions | 982 × 350 × 600 mm | 第 13 页 |
| Weight | 390 kg | 第 13 页 |
| Gear oil | N46 mechanical oil, about 5 L first fill | 第 12 页 |
| Rope grease | calcium base grease ZG-3 | 第 12 页 |
| Standards | ISO 7364, GB1392-85 | 第 10 页 |
备件与目录号
| 零件 | 编号 | 数量 | 说明书 |
|---|---|---|---|
| Spring | 241ZF200-01-13 | 1 | 第 16 页 |
| Ball bearing 6005 | GB/T276-94 | 4 | 第 16 页 |
| Ball bearing 6205 | GB/T276-94 | 1 | 第 16 页 |
| Oil seal PD25×40×10 | HG4-692-67 | 1 | 第 16 页 |
| Oil cup M10×1 | GB1152-84 | 1 | 第 16 页 |
| O-ring 14×2.4 | GB1235-76 | 2 | 第 16 页 |
| Washer 34×3.5 | GB1235-76 | 4 | 第 16 页 |
| Combined washer 33 | JB982-77 | 4 | 第 16 页 |
| Air control station | 241ZF213P1-05-0 | 2 | 第 15 页 |
来源:制造商说明书《PD10 pneumatic accommodation ladder winch》,共 34 页。页码以原文为准。作业前请核对船上的说明书。
本页为自动翻译。零件号、代码和页码与原文一致。