Zhenjiang PD10
Pneumatic accommodation ladder winch
Air-driven winch for hoisting and lowering the accommodation ladder, a short-time duty machine. A flanged air motor drives a split drum for two ropes through a reduction gear with a ratchet brake that limits the lowering speed; a hand crank on the gearbox shaft works it when there is no air, and a limit valve cuts the air while the crank is out. The manual covers readiness checks, operation with the three-position change valve, lubrication, rope renewal and opening the gearbox.
Mga training video
Mga maintenance procedure
Readiness for operation
- All operators must know the construction of the winch. p. 11
- The rope must leave the drum as on the general drawing; never wind it the wrong way. p. 11
- Check all connections for looseness, especially the rope end on the drum and the foundation bolts; check the brake. p. 11
- Clear any obstacles round the winch. p. 11
- Check the air fittings, pipes and air motor. p. 11
- Renew a rope with ten broken wires in 1 m or with reduced diameter. p. 11
- Check the oil level between the dipstick marks. p. 11
- Check the manual handle is stowed and the limit switch is reliable. p. 11
Operating the winch
- Pull out the pin on the accommodation ladder. p. 11
- Move the three-position change valve handle to lower, stop, hoist or capsize the ladder. p. 11
- To work by hand, keep the change valve in the middle, insert the handle on the square shaft end of the gearbox and crank. p. 12
Opening and reassembling the gearbox
- Unscrew the drain plug at the bottom of the gear box, drain the oil and remove the air motor. p. 12
- Strip the bolts of the big cover plate and pull it off together with the high-speed gear shaft; take out the bearings. p. 12
- Remove the big gear, ratchet and brake disc of the second stage in order. p. 12
- Reassemble in reverse order. p. 12Check the ratchet tooth direction; do not strip the ratchet unless necessary
- Refit only if the brake works without slipping. p. 12
Mga maintenance interval
| Item | Kailan | Gagawin | Manual |
|---|---|---|---|
| Gear box oil | after the first 50 h | Renew all oil and flush the case | p. 12 |
| Gear box oil | yearly | Change | p. 12 |
| Wire ropes | regularly | Smear with calcium base grease ZG-3 | p. 12 |
| Seals | regularly | Replace | p. 12 |
| Rope end on drum and foundation bolts | often | Check they are secure | p. 12 |
Technical specifications
| Rated load | 2 × 5 kN | p. 13 |
|---|---|---|
| Holding load | 2 × 5 kN | p. 13 |
| Rated hoisting speed | 0.14 m/s | p. 13 |
| Drum | Ø230 × (91 + 91) mm | p. 13 |
| Winding layers | 3 | p. 13 |
| Wire capacity | 2 × 15 m | p. 13 |
| Wire rope | 6 × 37 – Ø13 mm, 1700 MPa | p. 13 |
| Transmission ratio (air motor) | 75.43 | p. 13 |
| Transmission ratio (manual) | 30.73 | p. 13 |
| Total efficiency | 0.80 | p. 13 |
| Air motor | JFH 1/24, 4.41 kW, 890 r/min | p. 13 |
| Air consumption | 5.0 m³/min | p. 13 |
| Working pressure | 0.6 MPa | p. 13 |
| Overall dimensions | 982 × 350 × 600 mm | p. 13 |
| Weight | 390 kg | p. 13 |
| Gear oil | N46 mechanical oil, about 5 L first fill | p. 12 |
| Rope grease | calcium base grease ZG-3 | p. 12 |
| Standards | ISO 7364, GB1392-85 | p. 10 |
Spare parts at catalogue number
| Piyesa | Numero | Dami | Manual |
|---|---|---|---|
| Spring | 241ZF200-01-13 | 1 | p. 16 |
| Ball bearing 6005 | GB/T276-94 | 4 | p. 16 |
| Ball bearing 6205 | GB/T276-94 | 1 | p. 16 |
| Oil seal PD25×40×10 | HG4-692-67 | 1 | p. 16 |
| Oil cup M10×1 | GB1152-84 | 1 | p. 16 |
| O-ring 14×2.4 | GB1235-76 | 2 | p. 16 |
| Washer 34×3.5 | GB1235-76 | 4 | p. 16 |
| Combined washer 33 | JB982-77 | 4 | p. 16 |
| Air control station | 241ZF213P1-05-0 | 2 | p. 15 |
Pinagmulan: manual ng gumawa na “PD10 pneumatic accommodation ladder winch”, 34 pahina. Ang numero ng pahina ay ayon sa orihinal. Suriin ang manual sa barko bago magtrabaho.
Awtomatikong isinalin ang pahinang ito. Ang part number, code at pahina ay ayon sa orihinal.